/******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT 2016 STMicroelectronics</center></h2>
*
* Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/myliberty
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
* AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/*! \file
*
* \author
*
* \brief Platform header file. Defining platform independent functionality.
*
*/
/*
* PROJECT:
* $Revision: $
* LANGUAGE: ISO C99
*/
/*! \file platform.h
*
* \author Gustavo Patricio
*
* \brief Platform specific definition layer
*
* This should contain all platform and hardware specifics such as
* GPIO assignment, system resources, locks, IRQs, etc
*
* Each distinct platform/system/board must provide this definitions
* for all SW layers to use
*
*/
#ifndef PLATFORM_H
#define PLATFORM_H
/*
******************************************************************************
* INCLUDES
******************************************************************************
*/
#ifdef STM32L476xx
#include "stm32l4xx_hal.h"
#else
#include "stm32f4xx_hal.h"
#endif
#include <stdint.h>
#include <stdbool.h>
#include <limits.h>
#include "spi.h"
#include "timer.h"
#include "../../../../../../Downloads/STM32CubeExpansion_NFC5_V2.0.0 2/Projects/STM32F401RE-Nucleo/Applications/PollingTagDetect/Inc/main.h"
#include "logger.h"
/*
******************************************************************************
* GLOBAL DEFINES
******************************************************************************
*/
#define ST25R391X_SS_PIN SPI1_CS_Pin /*!< GPIO pin used for ST25R3911 SPI SS */
#define ST25R391X_SS_PORT SPI1_CS_GPIO_Port /*!< GPIO port used for ST25R3911 SPI SS port */
#define ST25R391X_INT_PIN IRQ_3911_Pin /*!< GPIO pin used for ST25R3911 External Interrupt */
#define ST25R391X_INT_PORT IRQ_3911_GPIO_Port /*!< GPIO port used for ST25R3911 External Interrupt */
#ifdef LED_FIELD_Pin
#define PLATFORM_LED_FIELD_PIN LED_FIELD_Pin /*!< GPIO pin used as field LED */
#endif
#ifdef LED_FIELD_GPIO_Port
#define PLATFORM_LED_FIELD_PORT LED_FIELD_GPIO_Port /*!< GPIO port used as field LED */
#endif
#define PLATFORM_LED_A_PIN LED_A_Pin /*!< GPIO pin used for LED A */
#define PLATFORM_LED_A_PORT LED_A_GPIO_Port /*!< GPIO port used for LED A */
#define PLATFORM_LED_B_PIN LED_B_Pin /*!< GPIO pin used for LED B */
#define PLATFORM_LED_B_PORT LED_B_GPIO_Port /*!< GPIO port used for LED B */
#define PLATFORM_LED_F_PIN LED_F_Pin /*!< GPIO pin used for LED F */
#define PLATFORM_LED_F_PORT LED_F_GPIO_Port /*!< GPIO port used for LED F */
#define PLATFORM_LED_V_PIN LED_V_Pin /*!< GPIO pin used for LED V */
#define PLATFORM_LED_V_PORT LED_V_GPIO_Port /*!< GPIO port used for LED V */
#define PLATFORM_LED_AP2P_PIN LED_AP2P_Pin /*!< GPIO pin used for LED AP2P */
#define PLATFORM_LED_AP2P_PORT LED_AP2P_GPIO_Port /*!< GPIO port used for LED AP2P*/
#define PLATFORM_USER_BUTTON_PIN B1_Pin /*!< GPIO pin user button */
#define PLATFORM_USER_BUTTON_PORT B1_GPIO_Port /*!< GPIO port user button */
/*
******************************************************************************
* GLOBAL MACROS
******************************************************************************
*/
#define platformProtectST25R391xComm() do{ globalCommProtectCnt++; __DSB();NVIC_DisableIRQ(EXTI0_IRQn);__DSB();__ISB();}while(0) /*!< Protect unique access to ST25R391x communication channel - IRQ disable on single thread environment (MCU) ; Mutex lock on a multi thread environment */
#define platformUnprotectST25R391xComm() do{ if (--globalCommProtectCnt==0U) {NVIC_EnableIRQ(EXTI0_IRQn);} }while(0) /*!< Unprotect unique access to ST25R391x communication channel - IRQ enable on a single thread environment (MCU) ; Mutex unlock on a multi thread environment */
#define platformProtectST25R391xIrqStatus() platformProtectST25R391xComm() /*!< Protect unique access to IRQ status var - IRQ disable on single thread environment (MCU) ; Mutex lock on a multi thread environment */
#define platformUnprotectST25R391xIrqStatus() platformUnprotectST25R391xComm() /*!< Unprotect the IRQ status var - IRQ enable on a single thread environment (MCU) ; Mutex unlock on a multi thread environment */
#define platformProtectWorker() /* Protect RFAL Worker/Task/Process from concurrent execution on multi thread platforms */
#define platformUnprotectWorker() /* Unprotect RFAL Worker/Task/Process from concurrent execution on multi thread platforms */
#define platformIrqST25R3911SetCallback( cb )
#define platformIrqST25R3911PinInitialize()
#define platformIrqST25R3916SetCallback( cb )
#define platformIrqST25R3916PinInitialize()
#define platformLedsInitialize() /*!< Initializes the pins used as LEDs to outputs*/
#define platformLedOff( port, pin ) platformGpioClear((port), (pin)) /*!< Turns the given LED Off */
#define platformLedOn( port, pin ) platformGpioSet((port), (pin)) /*!< Turns the given LED On */
#define platformLedToogle( port, pin ) platformGpioToogle((port), (pin)) /*!< Toogle the given LED */
#define platformGpioSet( port, pin ) HAL_GPIO_WritePin(port, pin, GPIO_PIN_SET) /*!< Turns the given GPIO High */
#define platformGpioClear( port, pin ) HAL_GPIO_WritePin(port, pin, GPIO_PIN_RESET) /*!< Turns the given GPIO Low */
#define platformGpioToogle( port, pin ) HAL_GPIO_TogglePin(port, pin) /*!< Toogles the given GPIO */
#define platformGpioIsHigh( port, pin ) (HAL_GPIO_ReadPin(port, pin) == GPIO_PIN_SET) /*!< Checks if the given LED is High */
#define platformGpioIsLow( port, pin ) (!platformGpioIsHigh(port, pin)) /*!< Checks if the given LED is Low */
#define platformTimerCreate( t ) timerCalculateTimer(t) /*!< Create a timer with the given time (ms) */
#define platformTimerIsExpired( timer ) timerIsExpired(timer) /*!< Checks if the given timer is expired */
#define platformDelay( t ) HAL_Delay( t ) /*!< Performs a delay for the given time (ms) */
#define platformGetSysTick() HAL_GetTick() /*!< Get System Tick ( 1 tick = 1 ms) */
#define platformSpiSelect() platformGpioClear( ST25R391X_SS_PORT, ST25R391X_SS_PIN ) /*!< SPI SS\CS: Chip|Slave Select */
#define platformSpiDeselect() platformGpioSet( ST25R391X_SS_PORT, ST25R391X_SS_PIN ) /*!< SPI SS\CS: Chip|Slave Deselect */
#define platformSpiTxRx( txBuf, rxBuf, len ) spiTxRx( (txBuf), (rxBuf), (len) ) /*!< SPI transceive */
#define platformI2CTx( txBuf, len ) /*!< I2C Transmit */
#define platformI2CRx( txBuf, len ) /*!< I2C Receive */
#define platformI2CStart() /*!< I2C Start condition */
#define platformI2CStop() /*!< I2C Stop condition */
#define platformI2CRepeatStart() /*!< I2C Repeat Start */
#define platformI2CSlaveAddrWR(add) /*!< I2C Slave address for Write operation */
#define platformI2CSlaveAddrRD(add) /*!< I2C Slave address for Read operation */
#define platformLog(...) logUsart(__VA_ARGS__) /*!< Log method */
/*
******************************************************************************
* GLOBAL VARIABLES
******************************************************************************
*/
extern uint8_t globalCommProtectCnt; /* Global Protection Counter provided per platform - instantiated in main.c */
/*
******************************************************************************
* RFAL FEATURES CONFIGURATION
******************************************************************************
*/
#define RFAL_FEATURE_LISTEN_MODE false /*!< Enable/Disable RFAL support for Listen Mode */
#define RFAL_FEATURE_WAKEUP_MODE true /*!< Enable/Disable RFAL support for the Wake-Up mode */
#define RFAL_FEATURE_NFCA true /*!< Enable/Disable RFAL support for NFC-A (ISO14443A) */
#define RFAL_FEATURE_NFCB true /*!< Enable/Disable RFAL support for NFC-B (ISO14443B) */
#define RFAL_FEATURE_NFCF true /*!< Enable/Disable RFAL support for NFC-F (FeliCa) */
#define RFAL_FEATURE_NFCV true /*!< Enable/Disable RFAL support for NFC-V (ISO15693) */
#define RFAL_FEATURE_T1T true /*!< Enable/Disable RFAL support for T1T (Topaz) */
#define RFAL_FEATURE_T2T true /*!< Enable/Disable RFAL support for T2T */
#define RFAL_FEATURE_T4T true /*!< Enable/Disable RFAL support for T4T */
#define RFAL_FEATURE_ST25TB true /*!< Enable/Disable RFAL support for ST25TB */
#define RFAL_FEATURE_ST25xV true /*!< Enable/Disable RFAL support for ST25TV/ST25DV */
#define RFAL_FEATURE_DYNAMIC_ANALOG_CONFIG false /*!< Enable/Disable Analog Configs to be dynamically updated (RAM) */
#define RFAL_FEATURE_DYNAMIC_POWER false /*!< Enable/Disable RFAL dynamic power support */
#define RFAL_FEATURE_ISO_DEP true /*!< Enable/Disable RFAL support for ISO-DEP (ISO14443-4) */
#define RFAL_FEATURE_ISO_DEP_POLL true /*!< Enable/Disable RFAL support for Poller mode (PCD) ISO-DEP (ISO14443-4) */
#define RFAL_FEATURE_ISO_DEP_LISTEN false /*!< Enable/Disable RFAL support for Listen mode (PICC) ISO-DEP (ISO14443-4) */
#define RFAL_FEATURE_NFC_DEP true /*!< Enable/Disable RFAL support for NFC-DEP (NFCIP1/P2P) */
#define RFAL_FEATURE_ISO_DEP_IBLOCK_MAX_LEN 256U /*!< ISO-DEP I-Block max length. Please use values as defined by rfalIsoDepFSx */
#define RFAL_FEATURE_ISO_DEP_APDU_MAX_LEN 1024U /*!< ISO-DEP APDU max length. Please use multiples of I-Block max length */
#endif /* PLATFORM_H */