/******************************************************************************
  * \attention
  *
  * <h2><center>&copy; COPYRIGHT 2016 STMicroelectronics</center></h2>
  *
  * Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        www.st.com/myliberty
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied,
  * AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
  * FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
******************************************************************************/

/*
 *      PROJECT:   ST25R391x firmware
 *      Revision:
 *      LANGUAGE:  ISO C99
 */

/*! \file rfal_analogConfig.h
 *
 *  \author bkam
 *
 *  \brief ST25R3911 Analog Configuration Settings
 *  
 */

#ifndef ST25R3911_ANALOGCONFIG_H
#define ST25R3911_ANALOGCONFIG_H

/*
 ******************************************************************************
 * INCLUDES
 ******************************************************************************
 */
#include "rfal_analogConfig.h"
#include "st25r3911_com.h"

/*
 ******************************************************************************
 * DEFINES
 ******************************************************************************
 */

/*
 ******************************************************************************
 * GLOBAL MACROS
 ******************************************************************************
 */

/*! Macro for Configuration Setting with only one register-mask-value set: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1] */
#define MODE_ENTRY_1_REG(MODE, R0, M0, V0)              \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 1, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0)

/*! Macro for Configuration Setting with only two register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1] */
#define MODE_ENTRY_2_REG(MODE, R0, M0, V0, R1, M1, V1)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 2, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1)

/*! Macro for Configuration Setting with only three register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_3_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 3, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \

/*! Macro for Configuration Setting with only four register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_4_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 4, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \

/*! Macro for Configuration Setting with only five register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_5_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 5, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \

/*! Macro for Configuration Setting with only six register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_6_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 6, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 
/*! Macro for Configuration Setting with only seven register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_7_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 7, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \

/*! Macro for Configuration Setting with only eight register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_8_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6, R7, M7, V7)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 8, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \
                                 , (uint8_t)((R7) >> 8), (uint8_t)((R7) & 0xFFU), (uint8_t)(M7), (uint8_t)(V7) \

/*! Macro for Configuration Setting with only nine register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_9_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6, R7, M7, V7, R8, M8, V8)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU), 9, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \
                                 , (uint8_t)((R7) >> 8), (uint8_t)((R7) & 0xFFU), (uint8_t)(M7), (uint8_t)(V7) \
                                 , (uint8_t)((R8) >> 8), (uint8_t)((R8) & 0xFFU), (uint8_t)(M8), (uint8_t)(V8) \

/*! Macro for Configuration Setting with only ten register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_10_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6, R7, M7, V7, R8, M8, V8, R9, M9, V9)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU),10, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \
                                 , (uint8_t)((R7) >> 8), (uint8_t)((R7) & 0xFFU), (uint8_t)(M7), (uint8_t)(V7) \
                                 , (uint8_t)((R8) >> 8), (uint8_t)((R8) & 0xFFU), (uint8_t)(M8), (uint8_t)(V8) \
                                 , (uint8_t)((R9) >> 8), (uint8_t)((R9) & 0xFFU), (uint8_t)(M9), (uint8_t)(V9) \

/*! Macro for Configuration Setting with eleven register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_11_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6, R7, M7, V7, R8, M8, V8, R9, M9, V9, R10, M10, V10)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU),11, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \
                                 , (uint8_t)((R7) >> 8), (uint8_t)((R7) & 0xFFU), (uint8_t)(M7), (uint8_t)(V7) \
                                 , (uint8_t)((R8) >> 8), (uint8_t)((R8) & 0xFFU), (uint8_t)(M8), (uint8_t)(V8) \
                                 , (uint8_t)((R9) >> 8), (uint8_t)((R9) & 0xFFU), (uint8_t)(M9), (uint8_t)(V9) \
                                 , (uint8_t)((R10) >> 8), (uint8_t)((R10) & 0xFFU), (uint8_t)(M10), (uint8_t)(V10) \

/*! Macro for Configuration Setting with twelve register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_12_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6, R7, M7, V7, R8, M8, V8, R9, M9, V9, R10, M10, V10, R11, M11, V11)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU),12, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \
                                 , (uint8_t)((R7) >> 8), (uint8_t)((R7) & 0xFFU), (uint8_t)(M7), (uint8_t)(V7) \
                                 , (uint8_t)((R8) >> 8), (uint8_t)((R8) & 0xFFU), (uint8_t)(M8), (uint8_t)(V8) \
                                 , (uint8_t)((R9) >> 8), (uint8_t)((R9) & 0xFFU), (uint8_t)(M9), (uint8_t)(V9) \
                                 , (uint8_t)((R10) >> 8), (uint8_t)((R10) & 0xFFU), (uint8_t)(M10), (uint8_t)(V10) \
                                 , (uint8_t)((R11) >> 8), (uint8_t)((R11) & 0xFFU), (uint8_t)(M11), (uint8_t)(V11) \

/*! Macro for Configuration Setting with thirteen register-mask-value sets: 
 *  - Configuration ID[2], Number of Register sets to follow[1], Register[2], Mask[1], Value[1], Register[2], Mask[1], Value[1], Register[2]... */
#define MODE_ENTRY_13_REG(MODE, R0, M0, V0, R1, M1, V1, R2, M2, V2, R3, M3, V3, R4, M4, V4, R5, M5, V5, R6, M6, V6, R7, M7, V7, R8, M8, V8, R9, M9, V9, R10, M10, V10, R11, M11, V11, R12, M12, V12)  \
    (uint8_t)((MODE) >> 8), (uint8_t)((MODE) & 0xFFU),13, (uint8_t)((R0) >> 8), (uint8_t)((R0) & 0xFFU), (uint8_t)(M0), (uint8_t)(V0) \
                                 , (uint8_t)((R1) >> 8), (uint8_t)((R1) & 0xFFU), (uint8_t)(M1), (uint8_t)(V1) \
                                 , (uint8_t)((R2) >> 8), (uint8_t)((R2) & 0xFFU), (uint8_t)(M2), (uint8_t)(V2) \
                                 , (uint8_t)((R3) >> 8), (uint8_t)((R3) & 0xFFU), (uint8_t)(M3), (uint8_t)(V3) \
                                 , (uint8_t)((R4) >> 8), (uint8_t)((R4) & 0xFFU), (uint8_t)(M4), (uint8_t)(V4) \
                                 , (uint8_t)((R5) >> 8), (uint8_t)((R5) & 0xFFU), (uint8_t)(M5), (uint8_t)(V5) \
                                 , (uint8_t)((R6) >> 8), (uint8_t)((R6) & 0xFFU), (uint8_t)(M6), (uint8_t)(V6) \
                                 , (uint8_t)((R7) >> 8), (uint8_t)((R7) & 0xFFU), (uint8_t)(M7), (uint8_t)(V7) \
                                 , (uint8_t)((R8) >> 8), (uint8_t)((R8) & 0xFFU), (uint8_t)(M8), (uint8_t)(V8) \
                                 , (uint8_t)((R9) >> 8), (uint8_t)((R9) & 0xFFU), (uint8_t)(M9), (uint8_t)(V9) \
                                 , (uint8_t)((R10) >> 8), (uint8_t)((R10) & 0xFFU), (uint8_t)(M10), (uint8_t)(V10) \
                                 , (uint8_t)((R11) >> 8), (uint8_t)((R11) & 0xFFU), (uint8_t)(M11), (uint8_t)(V11) \
                                 , (uint8_t)((R12) >> 8), (uint8_t)((R12) & 0xFFU), (uint8_t)(M12), (uint8_t)(V12) \
 
/* Setting for approximately 14%: */
#define AM_MOD_DRIVER_LEVEL_DEFAULT 0xb9 
/*
 ******************************************************************************
 * GLOBAL DATA TYPES
 ******************************************************************************
 */
/*  PRQA S 3406 1 # MISRA 8.6 - Externally generated table included by the library */   /*  PRQA S 1514 1 # MISRA 8.9 - Externally generated table included by the library */
 const uint8_t rfalAnalogConfigDefaultSettings[] = {
      //****** Default Analog Configuration for Chip-Specific Reset. ******/
      MODE_ENTRY_10_REG( (RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_INIT)
                      , ST25R3911_REG_OP_CONTROL,             0x30, 0x10 /* default to AM */
                      , ST25R3911_REG_IO_CONF1,               0x06, 0x06 /* MCUCLK: HF clk off */
                      , ST25R3911_REG_IO_CONF1,               (ST25R3911_REG_IO_CONF1_mask_out_cl | ST25R3911_REG_IO_CONF1_lf_clk_off), 0x07 /* MCUCLK: LF clk off */
                      , ST25R3911_REG_IO_CONF2,               0x18, 0x18 /* pull downs */
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_pm, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_pm /* increase digitizer window for PM */
                      , ST25R3911_REG_ANT_CAL_TARGET,         0xFF, 0x80 /* 90degrees */
                      , ST25R3911_REG_ANT_CAL_CONTROL,        0xF8, 0x00 /* trim value from calibrate antenna */
                      , ST25R3911_REG_AM_MOD_DEPTH_CONTROL,   ST25R3911_REG_AM_MOD_DEPTH_CONTROL_am_s, ST25R3911_REG_AM_MOD_DEPTH_CONTROL_am_s /* AM modulated level is defined by RFO AM Modulated Level Def Reg, fixed setting, no automatic adjustment */
                      , ST25R3911_REG_FIELD_THRESHOLD,        ST25R3911_REG_FIELD_THRESHOLD_mask_trg, ST25R3911_REG_FIELD_THRESHOLD_trg_75mV
                      , ST25R3911_REG_FIELD_THRESHOLD,        ST25R3911_REG_FIELD_THRESHOLD_mask_rfe, ST25R3911_REG_FIELD_THRESHOLD_rfe_75mV
                      )
                      
      //****** Default Analog Configuration for Poll NFC-A Tx. ******/
    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_RFO_AM_ON_LEVEL, 0xff, 0xf0 /* Used for 848 TX: very high AM to keep wave shapes */
                      )
                      
    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am,        0x00        /* OOK */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am,        0x00        /* OOK */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am,        0x00        /* OOK */
                      )

    , MODE_ENTRY_2_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_848 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,  ST25R3911_REG_AUX_tr_am,  ST25R3911_REG_AUX_tr_am       /* AM! */
                      , ST25R3911_REG_RFO_AM_ON_LEVEL, 0xff, 0xf0 /* Used for 848 TX: very high AM to keep wave shapes */
                      )

      //****** Default Analog Configuration for Poll NFC-A Rx. ******/
    , MODE_ENTRY_3_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF3, 0xff, 0x18
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x2U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_rx_tol, 0x00                                               /* rx_tol Off */
                      )
                                                                                  
    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1, 0x7f, 0x00
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1, 0x7f, 0x04
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1, 0x7f, 0x22
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCA | RFAL_ANALOG_CONFIG_BITRATE_848 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1, 0x7f, 0x22
                      )

      //****** Default Analog Configuration for Poll NFC-B Tx. ******/
    , MODE_ENTRY_2_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, ST25R3911_REG_AUX_tr_am   /* AM */
                      , ST25R3911_REG_RFO_AM_ON_LEVEL,        0xff, AM_MOD_DRIVER_LEVEL_DEFAULT                  /* Fixed driver for AM level: ~14% */
                      )

      //****** Default Analog Configuration for Poll NFC-B Rx. ******/
    , MODE_ENTRY_3_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF3, 0xff, 0x18
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_rx_tol, ST25R3911_REG_AUX_rx_tol                           /* rx_tol On as default */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x04
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x04
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x22
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_848 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x22
                      )
                      
    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_1695 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x6c
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCB | RFAL_ANALOG_CONFIG_BITRATE_3390 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x6c
                      )
                      
      //****** Default Analog Configuration for Poll NFC-F Tx. ******/
    , MODE_ENTRY_2_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, ST25R3911_REG_AUX_tr_am /* AM */
                      , ST25R3911_REG_RFO_AM_ON_LEVEL,        0xff, AM_MOD_DRIVER_LEVEL_DEFAULT /* Fixed driver for AM level: ~14% */
                      )

      //****** Default Analog Configuration for Poll NFC-F Common bitrate Rx. ******/
    , MODE_ENTRY_3_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF3, 0xff, 0x18
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_rx_tol, ST25R3911_REG_AUX_rx_tol                           /* rx_tol On as default */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x13   /* dev. from data sheet: lp 300kKz */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCF | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x0b   /* dev. from data sheet: lp 600kHz */
                      )
                      
    //****** Default Analog Configuration for Poll NFC-V Common bitrate Tx ******/
    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX, ST25R3911_REG_AUX_tr_am, 0x00
                      )

    //****** Default Analog Configuration for Poll NFC-V Common bitrate Rx ******/
    , MODE_ENTRY_4_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_NFCV | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1, 0x7f, 0x0c /* use filter settings from table 9: "Recommended for 424/484 kHz sub-carrier" */
                      , ST25R3911_REG_RX_CONF3, 0xff, 0x18
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_rx_tol, ST25R3911_REG_AUX_rx_tol                           /* rx_tol On as default */
                      )

      //****** Default Analog Configuration for Poll AP2P Common bitrate Tx. ******/
    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_RFO_AM_ON_LEVEL,        0xff, AM_MOD_DRIVER_LEVEL_DEFAULT /* Fixed driver for AM level: ~14% */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, 0x00 /* OOK */
                      )

    , MODE_ENTRY_2_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, ST25R3911_REG_AUX_tr_am /* AM */
                      , ST25R3911_REG_RFO_AM_ON_LEVEL,        0xff, AM_MOD_DRIVER_LEVEL_DEFAULT /* Fixed driver for AM level: ~14% */
                      )

    , MODE_ENTRY_2_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, ST25R3911_REG_AUX_tr_am /* AM */
                      , ST25R3911_REG_RFO_AM_ON_LEVEL,        0xff, AM_MOD_DRIVER_LEVEL_DEFAULT /* Fixed driver for AM level: ~14% */
                      )

      //****** Default Analog Configuration for Poll AP2P Common bitrate Rx. ******/
      
    , MODE_ENTRY_4_REG( (RFAL_ANALOG_CONFIG_TECH_CHIP | RFAL_ANALOG_CONFIG_CHIP_LISTEN_ON)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x45
                      , ST25R3911_REG_RX_CONF3,              (ST25R3911_REG_RX_CONF3_lim | ST25R3911_REG_RX_CONF3_rg_nfc), (ST25R3911_REG_RX_CONF3_lim | ST25R3911_REG_RX_CONF3_rg_nfc)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_rx_tol, ST25R3911_REG_AUX_rx_tol                            /* rx_tol On as default */
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                      )
                      
    , MODE_ENTRY_4_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF1,               0x7f, 0x45
                      , ST25R3911_REG_RX_CONF3,              (ST25R3911_REG_RX_CONF3_lim | ST25R3911_REG_RX_CONF3_rg_nfc), (ST25R3911_REG_RX_CONF3_lim | ST25R3911_REG_RX_CONF3_rg_nfc)
                      , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_rx_tol, ST25R3911_REG_AUX_rx_tol                            /* rx_tol On as default */
                      , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF3,               ST25R3911_REG_RX_CONF3_mask_rg1_am, 0xc0
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF3,               ST25R3911_REG_RX_CONF3_mask_rg1_am, 0x00
                      )

    , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_POLL | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
                      , ST25R3911_REG_RX_CONF3,               ST25R3911_REG_RX_CONF3_mask_rg1_am, 0x00
                      )

      //****** Default Analog Configuration for Listen AP2P Common bitrate Tx. ******/
      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_TX)
                        , ST25R3911_REG_RFO_AM_ON_LEVEL,        0xff, AM_MOD_DRIVER_LEVEL_DEFAULT /* Fixed driver for AM level: ~14% */
                        )

      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_TX)
                        , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, 0x00 /* OOK */
                        )

      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_TX)
                        , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, ST25R3911_REG_AUX_tr_am /* AM */
                        )

      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_TX)
                        , ST25R3911_REG_AUX,                    ST25R3911_REG_AUX_tr_am, ST25R3911_REG_AUX_tr_am /* AM */
                        )

        //****** Default Analog Configuration for Listen AP2P Common bitrate Rx. ******/
      , MODE_ENTRY_3_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_COMMON | RFAL_ANALOG_CONFIG_RX)
                        , ST25R3911_REG_RX_CONF1,               0x7f, 0x45
                        , ST25R3911_REG_RX_CONF3,              (ST25R3911_REG_RX_CONF3_lim | ST25R3911_REG_RX_CONF3_rg_nfc), (ST25R3911_REG_RX_CONF3_lim | ST25R3911_REG_RX_CONF3_rg_nfc)
                        , ST25R3911_REG_RX_CONF4,               ST25R3911_REG_RX_CONF4_mask_rg2_am, 0x1U<<ST25R3911_REG_RX_CONF4_shift_rg2_am /* increase digitizer window for AM */
                        )

      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_106 | RFAL_ANALOG_CONFIG_RX)
                        , ST25R3911_REG_RX_CONF3,               ST25R3911_REG_RX_CONF3_mask_rg1_am, 0xc0
                        )

      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_212 | RFAL_ANALOG_CONFIG_RX)
                        , ST25R3911_REG_RX_CONF3,               ST25R3911_REG_RX_CONF3_mask_rg1_am, 0x00
                        )

      , MODE_ENTRY_1_REG( (RFAL_ANALOG_CONFIG_LISTEN | RFAL_ANALOG_CONFIG_TECH_AP2P | RFAL_ANALOG_CONFIG_BITRATE_424 | RFAL_ANALOG_CONFIG_RX)
                        , ST25R3911_REG_RX_CONF3,               ST25R3911_REG_RX_CONF3_mask_rg1_am, 0x00
                        )
};

#endif /* ST25R3911_ANALOGCONFIG_H */