Added MarliBraille

MarlinBraille/pins_AZTEEG_X3.h

@@ -0,0 +1,99 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments
+ */
+
+#ifndef __AVR_ATmega2560__
+  #error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
+#endif
+
+#if HOTENDS > 2 || E_STEPPERS > 2
+  #error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
+#endif
+
+#if ENABLED(CASE_LIGHT_ENABLE)  && !PIN_EXISTS(CASE_LIGHT)
+  #define CASE_LIGHT_PIN 6     // must define it here or else RAMPS will define it
+#endif
+#define BOARD_NAME "Azteeg X3"
+
+#include "pins_RAMPS_13.h"
+
+//
+// Servos
+//
+#undef SERVO0_PIN
+#undef SERVO1_PIN
+#define SERVO0_PIN  44  // SERVO1 port
+#define SERVO1_PIN  55  // SERVO2 port
+
+//
+// LCD / Controller
+//
+#undef STAT_LED_RED_PIN
+#undef STAT_LED_BLUE_PIN
+
+#if ENABLED(VIKI2) || ENABLED(miniVIKI)
+
+  #undef DOGLCD_A0
+  #undef DOGLCD_CS
+  #undef BTN_ENC
+  #define DOGLCD_A0         31
+  #define DOGLCD_CS         32
+  #define BTN_ENC           12
+
+  #define STAT_LED_RED_PIN  64
+  #define STAT_LED_BLUE_PIN 63
+
+#else
+
+  #define STAT_LED_RED_PIN   6
+  #define STAT_LED_BLUE_PIN 11
+
+#endif
+
+//
+// Misc
+//
+#if ENABLED(CASE_LIGHT_ENABLE)  && PIN_EXISTS(CASE_LIGHT) && PIN_EXISTS(STAT_LED_RED) && STAT_LED_RED_PIN == CASE_LIGHT_PIN
+  #undef STAT_LED_RED_PIN
+#endif
+
+//
+// M3/M4/M5 - Spindle/Laser Control
+//
+#undef SPINDLE_LASER_PWM_PIN    // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
+#undef SPINDLE_LASER_ENABLE_PIN
+#undef SPINDLE_DIR_PIN
+
+#if ENABLED(SPINDLE_LASER_ENABLE)
+  #undef SDA                       // use EXP3 header
+  #undef SCL
+  #if SERVO0_PIN == 7
+    #undef SERVO0_PIN
+    #def SERVO0_PIN 11
+  #endif
+  #define SPINDLE_LASER_PWM_PIN     7  // MUST BE HARDWARE PWM
+  #define SPINDLE_LASER_ENABLE_PIN 20  // Pin should have a pullup!
+  #define SPINDLE_DIR_PIN          21
+#endif