no message

Repetier-Firmware 1.0.3/Repetier/Configuration.h

@@ -55,6 +55,12 @@
 #define FAN_THERMO_MAX_TEMP 60
 #define FAN_THERMO_THERMISTOR_PIN -1
 #define FAN_THERMO_THERMISTOR_TYPE 1
+#undef X_MAX_PIN
+#define X_MAX_PIN -1
+#undef Y_MAX_PIN
+#define Y_MAX_PIN -1
+#undef Z_MAX_PIN
+#define Z_MAX_PIN -1
 
 //#define EXTERNALSERIAL  use Arduino serial library instead of build in. Requires more ram, has only 63 byte input buffer.
 // Uncomment the following line if you are using Arduino compatible firmware made for Arduino version earlier then 1.0
@@ -65,9 +71,9 @@
 #define MIXING_EXTRUDER 0
 
 #define DRIVE_SYSTEM 0
-#define XAXIS_STEPS_PER_MM 80
-#define YAXIS_STEPS_PER_MM 80
-#define ZAXIS_STEPS_PER_MM 80
+#define XAXIS_STEPS_PER_MM 40
+#define YAXIS_STEPS_PER_MM 200
+#define ZAXIS_STEPS_PER_MM 4000
 #define EXTRUDER_FAN_COOL_TEMP 50
 #define PDM_FOR_EXTRUDER 0
 #define PDM_FOR_COOLER 0
@@ -81,7 +87,7 @@
 #define EXT0_X_OFFSET 0
 #define EXT0_Y_OFFSET 0
 #define EXT0_Z_OFFSET 0
-#define EXT0_STEPS_PER_MM 370
+#define EXT0_STEPS_PER_MM 
 #define EXT0_TEMPSENSOR_TYPE 8
 #define EXT0_TEMPSENSOR_PIN TEMP_0_PIN
 #define EXT0_HEATER_PIN HEATER_0_PIN
@@ -371,11 +377,11 @@ It also can add a delay to wait for spindle to run on full speed.
 #define STEPPER_INACTIVE_TIME 360L
 #define MAX_INACTIVE_TIME 0L
 #define MAX_FEEDRATE_X 200
-#define MAX_FEEDRATE_Y 200
-#define MAX_FEEDRATE_Z 2
-#define HOMING_FEEDRATE_X 40
-#define HOMING_FEEDRATE_Y 40
-#define HOMING_FEEDRATE_Z 2
+#define MAX_FEEDRATE_Y 40
+#define MAX_FEEDRATE_Z 25
+#define HOMING_FEEDRATE_X 100
+#define HOMING_FEEDRATE_Y 100
+#define HOMING_FEEDRATE_Z 10
 #define HOMING_ORDER HOME_ORDER_ZXY
 #define ZHOME_PRE_RAISE 0
 #define ZHOME_PRE_RAISE_DISTANCE 10
@@ -564,7 +570,7 @@ WARNING: Servos can draw a considerable amount of current. Make sure your system
 #define UI_AUTORETURN_TO_MENU_AFTER 30000
 #define FEATURE_UI_KEYS 0
 #define UI_ENCODER_SPEED 1
-#define UI_REVERSE_ENCODER 0
+#define UI_REVERSE_ENCODER 1
 #define UI_KEY_BOUNCETIME 10
 #define UI_KEY_FIRST_REPEAT 500
 #define UI_KEY_REDUCE_REPEAT 50
@@ -605,9 +611,9 @@ Values must be in range 1..255
     "baudrate": 115200,
     "bluetoothSerial": -1,
     "bluetoothBaudrate": 115200,
-    "xStepsPerMM": 80,
-    "yStepsPerMM": 80,
-    "zStepsPerMM": 80,
+    "xStepsPerMM": 40,
+    "yStepsPerMM": 200,
+    "zStepsPerMM": 4000,
     "xInvert": 0,
     "x2Invert": 0,
     "xInvertEnable": 0,
@@ -644,7 +650,7 @@ Values must be in range 1..255
             "waitRetractTemp": 150,
             "waitRetractUnits": 0,
             "waitRetract": 0,
-            "stepsPerMM": 370,
+            "stepsPerMM": null,
             "coolerPin": -1,
             "coolerSpeed": 255,
             "selectCommands": "",
@@ -691,15 +697,15 @@ Values must be in range 1..255
     "motherboard": 33,
     "driveSystem": 0,
     "xMaxSpeed": 200,
-    "xHomingSpeed": 40,
+    "xHomingSpeed": 100,
     "xTravelAcceleration": 1000,
     "xPrintAcceleration": 1000,
-    "yMaxSpeed": 200,
-    "yHomingSpeed": 40,
+    "yMaxSpeed": 40,
+    "yHomingSpeed": 100,
     "yTravelAcceleration": 1000,
     "yPrintAcceleration": 1000,
-    "zMaxSpeed": 2,
-    "zHomingSpeed": 2,
+    "zMaxSpeed": 25,
+    "zHomingSpeed": 10,
     "zTravelAcceleration": 100,
     "zPrintAcceleration": 100,
     "xMotor": {
@@ -835,7 +841,7 @@ Values must be in range 1..255
     "uiAutoReturnAfter": 30000,
     "featureKeys": "0",
     "uiEncoderSpeed": 1,
-    "uiReverseEncoder": "0",
+    "uiReverseEncoder": "1",
     "uiKeyBouncetime": 10,
     "uiKeyFirstRepeat": 500,
     "uiKeyReduceRepeat": 50,
@@ -965,9 +971,9 @@ Values must be in range 1..255
     "xMinPin": "ORIG_X_MIN_PIN",
     "yMinPin": "ORIG_Y_MIN_PIN",
     "zMinPin": "ORIG_Z_MIN_PIN",
-    "xMaxPin": "ORIG_X_MAX_PIN",
-    "yMaxPin": "ORIG_Y_MAX_PIN",
-    "zMaxPin": "ORIG_Z_MAX_PIN",
+    "xMaxPin": -1,
+    "yMaxPin": -1,
+    "zMaxPin": -1,
     "x2MinPin": -1,
     "y2MinPin": -1,
     "x2MaxPin": -1,