Trikarus/prusaslicer_profile/config.ini

# generated by PrusaSlicer 2.2.0+win64 on 2020-07-11 at 20:15:29 UTC
avoid_crossing_perimeters = 0
bed_custom_texture = trikarus-bed.svg
bed_shape = 498.097x43.5779,492.404x86.8241,482.963x129.41,469.846x171.01,453.154x211.309,433.013x250,409.576x286.788,383.022x321.394,353.553x353.553,321.394x383.022,286.788x409.576,250x433.013,211.309x453.154,171.01x469.846,129.41x482.963,86.8241x492.404,43.5779x498.097,3.06162e-14x500,-43.5779x498.097,-86.8241x492.404,-129.41x482.963,-171.01x469.846,-211.309x453.154,-250x433.013,-286.788x409.576,-321.394x383.022,-353.553x353.553,-383.022x321.394,-409.576x286.788,-433.013x250,-453.154x211.309,-469.846x171.01,-482.963x129.41,-492.404x86.8241,-498.097x43.5779,-500x6.12323e-14,-498.097x-43.5779,-492.404x-86.8241,-482.963x-129.41,-469.846x-171.01,-453.154x-211.309,-433.013x-250,-409.576x-286.788,-383.022x-321.394,-353.553x-353.553,-321.394x-383.022,-286.788x-409.576,-250x-433.013,-211.309x-453.154,-171.01x-469.846,-129.41x-482.963,-86.8241x-492.404,-43.5779x-498.097,-9.18485e-14x-500,43.5779x-498.097,86.8241x-492.404,129.41x-482.963,171.01x-469.846,211.309x-453.154,250x-433.013,286.788x-409.576,321.394x-383.022,353.553x-353.553,383.022x-321.394,409.576x-286.788,433.013x-250,453.154x-211.309,469.846x-171.01,482.963x-129.41,492.404x-86.8241,498.097x-43.5779,500x-1.22465e-13
bed_temperature = 0
before_layer_gcode = 
between_objects_gcode = 
bottom_fill_pattern = rectilinear
bottom_solid_layers = 2
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
clip_multipart_objects = 1
colorprint_heights = 
complete_objects = 0
cooling = 1
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_acceleration = 0
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
disable_fan_first_layers = 2
dont_support_bridges = 0
draft_shield = 0
duplicate_distance = 6
elefant_foot_compensation = 0.2
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = ;PrusaSlicer automatically generates M107 command at the end which turns off the fan. But we want to cool down the last millimeters too for some more seconds\nM106 S255 ;re-enable blower fan\nM104 S0 ;turn off temperature\nG91 ;relative coordinates\nG0 Z3 ;move extruder 3 mm higher\nG90 ;absolute coordinates\nG4 S20 ;wait 30 seconds\nM106 S0 ;then turn off the blower fan again
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 1.57
external_perimeter_speed = 75%
external_perimeters_first = 0
extra_loading_move = -2
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #0080FF
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 1.57
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 18.81
filament_density = 1.25
filament_deretract_speed = nil
filament_diameter = 1.8
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = "offical data from spool:\n- density: 1.25 g/cm^3\n- diameter: 1.75 mm +/- 0.05 mm (90% of all filament spools below +/- 0.02 mm)\n- print temperature: 205 C +/- 10 C"
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = "Trikarus - Redline Filament PLA"
filament_soluble = 0
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
fill_angle = 45
fill_density = 5%
fill_pattern = gyroid
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 1.47
first_layer_height = 110%
first_layer_speed = 20%
first_layer_temperature = 205
gap_fill_speed = 40
gcode_comments = 0
gcode_flavor = marlin
gcode_label_objects = 0
high_current_on_filament_swap = 0
host_type = duet
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 1.57
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 45
interface_shells = 0
layer_gcode = 
layer_height = 1
machine_max_acceleration_e = 1000,1000
machine_max_acceleration_extruding = 1500,1500
machine_max_acceleration_retracting = 1500,1500
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 1000,1000
machine_max_acceleration_z = 1000,1000
machine_max_feedrate_e = 3600,3600
machine_max_feedrate_x = 9500,9500
machine_max_feedrate_y = 9500,9500
machine_max_feedrate_z = 9500,9500
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.2
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_fan_speed = 100
max_layer_height = 1.4
max_print_height = 2000
max_print_speed = 50
max_volumetric_speed = 110
min_fan_speed = 65
min_layer_height = 0.3
min_print_speed = 10
min_skirt_length = 100
notes = 
nozzle_diameter = 1.4
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
parking_pos_retraction = 92
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 1.57
perimeter_speed = 35
perimeters = 2
post_process = 
print_host = 
print_settings_id = Trikarus
printer_model = 
printer_notes = - M203 command in PrusaSlicer takes mm/second but Duet RRF takes those values as mm/minute. So you need to enter the mm/minute values without conversion\n- M73 not supported by RRF
printer_settings_id = Trikarus
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
raft_layers = 0
remaining_times = 0
resolution = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 10
retract_lift = 1.5
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
seam_position = nearest
serial_port = 
serial_speed = 250000
silent_mode = 1
single_extruder_multi_material = 0
single_extruder_multi_material_priming = 1
skirt_distance = 40
skirt_height = 1
skirts = 1
slice_closing_radius = 0.049
slowdown_below_layer_time = 5
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 1.57
solid_infill_speed = 35
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n"
start_gcode = G28 ;reset coordinates - you must delete the files homex.g and homey.g on Duet Web Control because they contain dangerious moves when using default DWC config\n;deactivated stuff:\n;G92 X0 Y0 Z0 ;reset coordinates - does not always work so we use preceding G28\n;M106 P2 S0 ;turn off laser pointers - this is done by sms_prepare.sh script. no need to do twice\nM117 "Starting new GCode print job" ;M291 PMESSAGE does not work here. It just won't be displayed while printing
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 1
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 1.22
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 4
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 10
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 50%
temperature = 215
thin_walls = 1
threads = 8
thumbnails = 
toolchange_gcode = 
top_fill_pattern = rectilinear
top_infill_extrusion_width = 1.4
top_solid_infill_speed = 30
top_solid_layers = 2
top_solid_min_thickness = 0
travel_speed = 130
use_firmware_retraction = 1
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
wipe_into_infill = 0
wipe_into_objects = 0
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
wiping_volumes_extruders = 70,70
wiping_volumes_matrix = 0
xy_size_compensation = 0
z_offset = 0