changed more print parameters:

- extrusion widths
- enabled volumetric E
- end gcode routine
- ironing distance raised (too much heat with lower values)
- speed adjustments

prusaslicer_profile/config.ini

@@ -1,253 +0,0 @@
-# generated by PrusaSlicer 2.3.0+win64 on 2021-06-19 at 21:40:35 UTC
-avoid_crossing_perimeters = 0
-avoid_crossing_perimeters_max_detour = 0
-bed_custom_model = trikarus-bed.stl
-bed_custom_texture = trikarus-bed.svg
-bed_shape = 498.097x43.5779,492.404x86.8241,482.963x129.41,469.846x171.01,453.154x211.309,433.013x250,409.576x286.788,383.022x321.394,353.553x353.553,321.394x383.022,286.788x409.576,250x433.013,211.309x453.154,171.01x469.846,129.41x482.963,86.8241x492.404,43.5779x498.097,3.06162e-14x500,-43.5779x498.097,-86.8241x492.404,-129.41x482.963,-171.01x469.846,-211.309x453.154,-250x433.013,-286.788x409.576,-321.394x383.022,-353.553x353.553,-383.022x321.394,-409.576x286.788,-433.013x250,-453.154x211.309,-469.846x171.01,-482.963x129.41,-492.404x86.8241,-498.097x43.5779,-500x6.12323e-14,-498.097x-43.5779,-492.404x-86.8241,-482.963x-129.41,-469.846x-171.01,-453.154x-211.309,-433.013x-250,-409.576x-286.788,-383.022x-321.394,-353.553x-353.553,-321.394x-383.022,-286.788x-409.576,-250x-433.013,-211.309x-453.154,-171.01x-469.846,-129.41x-482.963,-86.8241x-492.404,-43.5779x-498.097,-9.18485e-14x-500,43.5779x-498.097,86.8241x-492.404,129.41x-482.963,171.01x-469.846,211.309x-453.154,250x-433.013,286.788x-409.576,321.394x-383.022,353.553x-353.553,383.022x-321.394,409.576x-286.788,433.013x-250,453.154x-211.309,469.846x-171.01,482.963x-129.41,492.404x-86.8241,498.097x-43.5779,500x-1.22465e-13
-bed_temperature = 0
-before_layer_gcode = 
-between_objects_gcode = 
-bottom_fill_pattern = rectilinear
-bottom_solid_layers = 2
-bottom_solid_min_thickness = 0
-bridge_acceleration = 0
-bridge_angle = 0
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 60
-brim_width = 0
-clip_multipart_objects = 1
-color_change_gcode = M600
-colorprint_heights = 
-complete_objects = 0
-cooling = 1
-cooling_tube_length = 5
-cooling_tube_retraction = 91.5
-default_acceleration = 0
-default_filament_profile = ""
-default_print_profile = 
-deretract_speed = 0
-disable_fan_first_layers = 2
-dont_support_bridges = 0
-draft_shield = 0
-duplicate_distance = 6
-elefant_foot_compensation = 0.2
-end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
-end_gcode = ;PrusaSlicer automatically generates M107 command at the end which turns off the fan. But we want to cool down the last millimeters too for some more seconds\nM106 S255 ;re-enable blower fan\nM104 S0 ;turn off temperature\nG91 ;relative coordinates\nG0 Z3 ;move extruder 3 mm higher\nG90 ;absolute coordinates\nG4 S20 ;wait 30 seconds\nM106 S0 ;then turn off the blower fan again
-ensure_vertical_shell_thickness = 1
-external_perimeter_extrusion_width = 1.57
-external_perimeter_speed = 75%
-external_perimeters_first = 0
-extra_loading_move = -2
-extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extruder_colour = #0080FF
-extruder_offset = 0x0
-extrusion_axis = E
-extrusion_multiplier = 1
-extrusion_width = 1.57
-fan_always_on = 0
-fan_below_layer_time = 60
-filament_colour = #C0C0C0
-filament_cooling_final_speed = 3.4
-filament_cooling_initial_speed = 2.2
-filament_cooling_moves = 4
-filament_cost = 18.81
-filament_density = 1.24
-filament_deretract_speed = nil
-filament_diameter = 1.75
-filament_load_time = 0
-filament_loading_speed = 28
-filament_loading_speed_start = 3
-filament_max_volumetric_speed = 0
-filament_minimal_purge_on_wipe_tower = 15
-filament_notes = "offical data from spool:\n- density: 1.24 g/cm^3\n- diameter: 1.75 mm +/- 0.05 mm\n- print temperature: 215 C +/- 15 C"
-filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
-filament_retract_before_travel = nil
-filament_retract_before_wipe = nil
-filament_retract_layer_change = nil
-filament_retract_length = nil
-filament_retract_lift = nil
-filament_retract_lift_above = nil
-filament_retract_lift_below = nil
-filament_retract_restart_extra = nil
-filament_retract_speed = nil
-filament_settings_id = "Trikarus - Das Filament PLA"
-filament_soluble = 0
-filament_spool_weight = 0
-filament_toolchange_delay = 0
-filament_type = PLA
-filament_unload_time = 0
-filament_unloading_speed = 90
-filament_unloading_speed_start = 100
-filament_vendor = (Unknown)
-filament_wipe = nil
-fill_angle = 45
-fill_density = 5%
-fill_pattern = gyroid
-first_layer_acceleration = 0
-first_layer_bed_temperature = 0
-first_layer_extrusion_width = 1.47
-first_layer_height = 100%
-first_layer_speed = 20%
-first_layer_temperature = 205
-full_fan_speed_layer = 0
-gap_fill_speed = 40
-gcode_comments = 0
-gcode_flavor = marlin
-gcode_label_objects = 0
-high_current_on_filament_swap = 0
-host_type = duet
-infill_acceleration = 0
-infill_anchor = 600%
-infill_anchor_max = 50
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 1.57
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 35%
-infill_speed = 45
-interface_shells = 0
-ironing = 1
-ironing_flowrate = 15%
-ironing_spacing = 0.4
-ironing_speed = 20
-ironing_type = top
-layer_gcode = 
-layer_height = 1
-machine_limits_usage = emit_to_gcode
-machine_max_acceleration_e = 1000,1000
-machine_max_acceleration_extruding = 1500,1500
-machine_max_acceleration_retracting = 1500,1500
-machine_max_acceleration_x = 1000,1000
-machine_max_acceleration_y = 1000,1000
-machine_max_acceleration_z = 1000,1000
-machine_max_feedrate_e = 3600,3600
-machine_max_feedrate_x = 9500,9500
-machine_max_feedrate_y = 9500,9500
-machine_max_feedrate_z = 9500,9500
-machine_max_jerk_e = 2.5,2.5
-machine_max_jerk_x = 10,10
-machine_max_jerk_y = 10,10
-machine_max_jerk_z = 0.2,0.2
-machine_min_extruding_rate = 0,0
-machine_min_travel_rate = 0,0
-max_fan_speed = 100
-max_layer_height = 1.4
-max_print_height = 1200
-max_print_speed = 50
-max_volumetric_speed = 110
-min_fan_speed = 65
-min_layer_height = 0.3
-min_print_speed = 10
-min_skirt_length = 100
-notes = 
-nozzle_diameter = 1.4
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-parking_pos_retraction = 92
-pause_print_gcode = M601
-perimeter_acceleration = 0
-perimeter_extruder = 1
-perimeter_extrusion_width = 1.57
-perimeter_speed = 35
-perimeters = 2
-physical_printer_settings_id = 
-post_process = 
-print_host = 
-print_settings_id = Trikarus
-printer_model = 
-printer_notes = - M203 command in PrusaSlicer takes mm/second but Duet RRF takes those values as mm/minute. So you need to enter the mm/minute values without conversion\n- M73 not supported by RRF
-printer_settings_id = Trikarus
-printer_technology = FFF
-printer_variant = 
-printer_vendor = 
-printhost_apikey = 
-printhost_cafile = 
-raft_layers = 0
-remaining_times = 0
-resolution = 0
-retract_before_travel = 20
-retract_before_wipe = 0%
-retract_layer_change = 1
-retract_length = 3
-retract_length_toolchange = 10
-retract_lift = 1.5
-retract_lift_above = 0
-retract_lift_below = 0
-retract_restart_extra = 0
-retract_restart_extra_toolchange = 0
-retract_speed = 60
-seam_position = nearest
-silent_mode = 1
-single_extruder_multi_material = 0
-single_extruder_multi_material_priming = 1
-skirt_distance = 40
-skirt_height = 1
-skirts = 1
-slice_closing_radius = 0.049
-slowdown_below_layer_time = 5
-small_perimeter_speed = 30
-solid_infill_below_area = 70
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 1.57
-solid_infill_speed = 35
-spiral_vase = 0
-standby_temperature_delta = -5
-start_filament_gcode = "; Filament gcode\n"
-start_gcode = G28 ;reset coordinates - you must delete the files homex.g and homey.g on Duet Web Control because they contain dangerious moves when using default DWC config\n;deactivated stuff:\n;G92 X0 Y0 Z0 ;reset coordinates - does not always work so we use preceding G28\n;M106 P2 S0 ;turn off laser pointers - this is done by sms_prepare.sh script. no need to do twice\nM117 "Starting new GCode print job" ;M291 PMESSAGE does not work here. It just won't be displayed while printing
-support_material = 1
-support_material_angle = 0
-support_material_auto = 1
-support_material_buildplate_only = 1
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 1.22
-support_material_interface_contact_loops = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 3
-support_material_interface_spacing = 4
-support_material_interface_speed = 100%
-support_material_pattern = rectilinear
-support_material_spacing = 10
-support_material_speed = 45
-support_material_synchronize_layers = 0
-support_material_threshold = 0
-support_material_with_sheath = 1
-support_material_xy_spacing = 50%
-temperature = 215
-template_custom_gcode = 
-thin_walls = 0
-threads = 8
-thumbnails = 
-toolchange_gcode = 
-top_fill_pattern = rectilinear
-top_infill_extrusion_width = 1.4
-top_solid_infill_speed = 30
-top_solid_layers = 4
-top_solid_min_thickness = 0
-travel_speed = 130
-use_firmware_retraction = 1
-use_relative_e_distances = 0
-use_volumetric_e = 0
-variable_layer_height = 1
-wipe = 0
-wipe_into_infill = 0
-wipe_into_objects = 0
-wipe_tower = 0
-wipe_tower_bridging = 10
-wipe_tower_no_sparse_layers = 0
-wipe_tower_rotation_angle = 0
-wipe_tower_width = 60
-wipe_tower_x = 180
-wipe_tower_y = 140
-wiping_volumes_extruders = 70,70
-wiping_volumes_matrix = 0
-xy_size_compensation = 0
-z_offset = 0

prusaslicer_profile/filament/Trikarus - Das Filament PLA.ini

@@ -0,0 +1,55 @@
+# generated by PrusaSlicer 2.2.0+win64 on 2020-10-24 at 12:17:42 UTC
+bed_temperature = 0
+bridge_fan_speed = 100
+compatible_printers = Trikarus
+compatible_printers_condition = 
+compatible_prints = Trikarus
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #C0C0C0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 18.81
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "offical data from spool:\n- density: 1.24 g/cm^3\n- diameter: 1.75 mm +/- 0.05 mm\n- print temperature: 215 C +/- 15 C"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 0
+first_layer_temperature = 205
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 65
+min_print_speed = 10
+slowdown_below_layer_time = 5
+start_filament_gcode = "; Filament gcode\n"
+temperature = 215

prusaslicer_profile/filament/Trikarus - Prusa PLA.ini

@@ -0,0 +1,55 @@
+# generated by PrusaSlicer 2.2.0+win64 on 2020-07-07 at 17:29:59 UTC
+bed_temperature = 0
+bridge_fan_speed = 100
+compatible_printers = Trikarus
+compatible_printers_condition = 
+compatible_prints = Trikarus
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_colour = #C0C0C0
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 18.81
+filament_density = 1.25
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "offical data from spool:\n- density: ?\n- diameter: 1.75 mm +/- 0.05 mm\n- print temperature: 200 C -220 C"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 0
+first_layer_temperature = 205
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 65
+min_print_speed = 10
+slowdown_below_layer_time = 5
+start_filament_gcode = "; Filament gcode\n"
+temperature = 225

prusaslicer_profile/filament/Trikarus - Redline Filament PLA.ini

@@ -0,0 +1,55 @@
+# generated by PrusaSlicer 2.2.0+win64 on 2020-07-10 at 21:57:59 UTC
+bed_temperature = 0
+bridge_fan_speed = 100
+compatible_printers = Trikarus
+compatible_printers_condition = 
+compatible_prints = Trikarus
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 2
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 18.81
+filament_density = 1.25
+filament_deretract_speed = nil
+filament_diameter = 1.8
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = "offical data from spool:\n- density: 1.25 g/cm^3\n- diameter: 1.75 mm +/- 0.05 mm (90% of all filament spools below +/- 0.02 mm)\n- print temperature: 205 C +/- 10 C"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = (Unknown)
+filament_wipe = nil
+first_layer_bed_temperature = 0
+first_layer_temperature = 205
+inherits = 
+max_fan_speed = 100
+min_fan_speed = 65
+min_print_speed = 10
+slowdown_below_layer_time = 5
+start_filament_gcode = "; Filament gcode\n"
+temperature = 215

prusaslicer_profile/print/Trikarus.ini

@@ -0,0 +1,122 @@
+# generated by PrusaSlicer 2.3.1+win64 on 2021-06-20 at 13:50:41 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = rectilinear
+bottom_solid_layers = 2
+bottom_solid_min_thickness = 0
+bridge_acceleration = 0
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 33
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = Trikarus
+compatible_printers_condition = 
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+draft_shield = 0
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 100%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 200%
+first_layer_height = 100%
+first_layer_speed = 20%
+gap_fill_speed = 11
+gcode_comments = 0
+gcode_label_objects = 0
+infill_acceleration = 0
+infill_anchor = 600%
+infill_anchor_max = 50
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 35%
+infill_speed = 45
+inherits = 
+interface_shells = 0
+ironing = 1
+ironing_flowrate = 10%
+ironing_spacing = 0.7
+ironing_speed = 15
+ironing_type = top
+layer_height = 1
+max_print_speed = 50
+max_volumetric_speed = 110
+min_skirt_length = 100
+notes = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 33
+perimeters = 2
+post_process = 
+print_settings_id = Trikarus
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 1
+skirt_distance = 40
+skirt_height = 1
+skirts = 1
+slice_closing_radius = 0.049
+small_perimeter_speed = 25%
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 33%
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_buildplate_only = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 4
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 8
+support_material_speed = 35
+support_material_synchronize_layers = 0
+support_material_threshold = 0
+support_material_with_sheath = 1
+support_material_xy_spacing = 50%
+thin_walls = 0
+threads = 8
+top_fill_pattern = rectilinear
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 60%
+top_solid_layers = 4
+top_solid_min_thickness = 0
+travel_speed = 130
+wipe_tower = 0
+wipe_tower_bridging = 10
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 180
+wipe_tower_y = 140
+xy_size_compensation = 0

prusaslicer_profile/printer/Trikarus.ini

@@ -0,0 +1,77 @@
+# generated by PrusaSlicer 2.3.1+win64 on 2021-06-20 at 13:47:44 UTC
+bed_custom_model = C:\\Users\\tomate\\AppData\\Roaming\\PrusaSlicer\\printer\\trikarus-bed.stl
+bed_custom_texture = C:\\Users\\tomate\\AppData\\Roaming\\PrusaSlicer\\printer\\trikarus-bed.svg
+bed_shape = 498.097x43.5779,492.404x86.8241,482.963x129.41,469.846x171.01,453.154x211.309,433.013x250,409.576x286.788,383.022x321.394,353.553x353.553,321.394x383.022,286.788x409.576,250x433.013,211.309x453.154,171.01x469.846,129.41x482.963,86.8241x492.404,43.5779x498.097,3.06162e-14x500,-43.5779x498.097,-86.8241x492.404,-129.41x482.963,-171.01x469.846,-211.309x453.154,-250x433.013,-286.788x409.576,-321.394x383.022,-353.553x353.553,-383.022x321.394,-409.576x286.788,-433.013x250,-453.154x211.309,-469.846x171.01,-482.963x129.41,-492.404x86.8241,-498.097x43.5779,-500x6.12323e-14,-498.097x-43.5779,-492.404x-86.8241,-482.963x-129.41,-469.846x-171.01,-453.154x-211.309,-433.013x-250,-409.576x-286.788,-383.022x-321.394,-353.553x-353.553,-321.394x-383.022,-286.788x-409.576,-250x-433.013,-211.309x-453.154,-171.01x-469.846,-129.41x-482.963,-86.8241x-492.404,-43.5779x-498.097,-9.18485e-14x-500,43.5779x-498.097,86.8241x-492.404,129.41x-482.963,171.01x-469.846,211.309x-453.154,250x-433.013,286.788x-409.576,321.394x-383.022,353.553x-353.553,383.022x-321.394,409.576x-286.788,433.013x-250,453.154x-211.309,469.846x-171.01,482.963x-129.41,492.404x-86.8241,498.097x-43.5779,500x-1.22465e-13
+before_layer_gcode = 
+between_objects_gcode = 
+color_change_gcode = M600
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = ""
+default_print_profile = 
+deretract_speed = 0
+end_gcode = ;PrusaSlicer automatically generates M107 command at the end which turns off the fan. But we want to cool down the last millimeters too for some more seconds\nM106 S255 ;re-enable blower fan\nM104 S0 ;turn off temperature\nG90 ;absolute coordinates\n{if layer_z + 100 < max_print_height}G1 Z{z_offset + min(layer_z + 100, max_print_height)}{endif} ; Move print head up +100 mm if enough space is available\nG4 S20 ;wait 30 seconds\nM106 S0 ;then turn off the blower fan again
+extra_loading_move = -2
+extruder_colour = #0080FF
+extruder_offset = 0x0
+gcode_flavor = marlin
+high_current_on_filament_swap = 0
+host_type = duet
+inherits = 
+layer_gcode = 
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 1000,1000
+machine_max_acceleration_extruding = 1500,1500
+machine_max_acceleration_retracting = 1500,1500
+machine_max_acceleration_x = 1000,1000
+machine_max_acceleration_y = 1000,1000
+machine_max_acceleration_z = 1000,1000
+machine_max_feedrate_e = 3600,3600
+machine_max_feedrate_x = 9500,9500
+machine_max_feedrate_y = 9500,9500
+machine_max_feedrate_z = 9500,9500
+machine_max_jerk_e = 2.5,2.5
+machine_max_jerk_x = 10,10
+machine_max_jerk_y = 10,10
+machine_max_jerk_z = 0.2,0.2
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 1.4
+max_print_height = 1200
+min_layer_height = 0.3
+nozzle_diameter = 1.4
+parking_pos_retraction = 92
+pause_print_gcode = M601
+print_host = 
+printer_model = 
+printer_notes = - M203 command in PrusaSlicer takes mm/second but Duet RRF takes those values as mm/minute. So you need to enter the mm/minute values without conversion\n- M73 not supported by RRF
+printer_settings_id = Trikarus
+printer_technology = FFF
+printer_variant = 
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 20
+retract_before_wipe = 0%
+retract_layer_change = 1
+retract_length = 3
+retract_length_toolchange = 10
+retract_lift = 1.5
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 60
+silent_mode = 1
+single_extruder_multi_material = 0
+start_gcode = G28 ;reset coordinates - you must delete the files homex.g and homey.g on Duet Web Control because they contain dangerious moves when using default DWC config\n;deactivated stuff:\n;G92 X0 Y0 Z0 ;reset coordinates - does not always work so we use preceding G28\n;M106 P2 S0 ;turn off laser pointers - this is done by sms_prepare.sh script. no need to do twice\nM117 "Starting new GCode print job" ;M291 PMESSAGE does not work here. It just won't be displayed while printing
+template_custom_gcode = 
+thumbnails = 
+toolchange_gcode = 
+use_firmware_retraction = 1
+use_relative_e_distances = 0
+use_volumetric_e = 1
+variable_layer_height = 1
+wipe = 0
+z_offset = 0