# generated by PrusaSlicer 2.2.0 on 2021-07-25 at 16:56:35 UTC
bed_custom_model = /home/tomate/.PrusaSlicer/printer/trikarus-bed.stl
bed_custom_texture = /home/tomate/.PrusaSlicer/printer/trikarus-bed.svg
bed_shape = 498.097x43.5779,492.404x86.8241,482.963x129.41,469.846x171.01,453.154x211.309,433.013x250,409.576x286.788,383.022x321.394,353.553x353.553,321.394x383.022,286.788x409.576,250x433.013,211.309x453.154,171.01x469.846,129.41x482.963,86.8241x492.404,43.5779x498.097,3.06162e-14x500,-43.5779x498.097,-86.8241x492.404,-129.41x482.963,-171.01x469.846,-211.309x453.154,-250x433.013,-286.788x409.576,-321.394x383.022,-353.553x353.553,-383.022x321.394,-409.576x286.788,-433.013x250,-453.154x211.309,-469.846x171.01,-482.963x129.41,-492.404x86.8241,-498.097x43.5779,-500x6.12323e-14,-498.097x-43.5779,-492.404x-86.8241,-482.963x-129.41,-469.846x-171.01,-453.154x-211.309,-433.013x-250,-409.576x-286.788,-383.022x-321.394,-353.553x-353.553,-321.394x-383.022,-286.788x-409.576,-250x-433.013,-211.309x-453.154,-171.01x-469.846,-129.41x-482.963,-86.8241x-492.404,-43.5779x-498.097,-9.18485e-14x-500,43.5779x-498.097,86.8241x-492.404,129.41x-482.963,171.01x-469.846,211.309x-453.154,250x-433.013,286.788x-409.576,321.394x-383.022,353.553x-353.553,383.022x-321.394,409.576x-286.788,433.013x-250,453.154x-211.309,469.846x-171.01,482.963x-129.41,492.404x-86.8241,498.097x-43.5779,500x-1.22465e-13
before_layer_gcode = 
between_objects_gcode = 
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = ""
default_print_profile = 
deretract_speed = 0
end_gcode = ;PrusaSlicer automatically generates M107 command at the end which turns off the fan. But we want to cool down the last millimeters too for some more seconds\nM106 S255 ;re-enable blower fan\nM104 S0 ;turn off temperature\nG90 ;absolute coordinates\n{if layer_z + 100 < max_print_height}G1 Z{z_offset + min(layer_z + 100, max_print_height)}{endif} ; Move print head up +100 mm if enough space is available\nG4 S20 ;wait 30 seconds\nM106 S0 ;then turn off the blower fan again
extra_loading_move = -2
extruder_colour = #0080FF
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = duet
inherits = 
layer_gcode = 
machine_max_acceleration_e = 1000,1000
machine_max_acceleration_extruding = 1500,1500
machine_max_acceleration_retracting = 1500,1500
machine_max_acceleration_x = 1000,1000
machine_max_acceleration_y = 1000,1000
machine_max_acceleration_z = 1000,1000
machine_max_feedrate_e = 3600,3600
machine_max_feedrate_x = 9500,9500
machine_max_feedrate_y = 9500,9500
machine_max_feedrate_z = 9500,9500
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.2
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 1.4
max_print_height = 1200
min_layer_height = 0.3
nozzle_diameter = 1.4
parking_pos_retraction = 92
print_host = 
printer_model = 
printer_notes = - M203 command in PrusaSlicer takes mm/second but Duet RRF takes those values as mm/minute. So you need to enter the mm/minute values without conversion\n- M73 not supported by RRF\n- retraction is configured by firmware and is set to M207 S0.8 R0.0 F2500 Z0.8 (0.8 mm) - so we skip to use the suggestion of 3 mm in PrusaSlicer (it is disabled)
printer_settings_id = Trikarus
printer_technology = FFF
printer_variant = 
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 30
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 10
retract_lift = 1.5
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
serial_port = 
serial_speed = 250000
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G28 ;reset coordinates - you must delete the files homex.g and homey.g on Duet Web Control because they contain dangerious moves when using default DWC config\n;deactivated stuff:\n;G92 X0 Y0 Z0 ;reset coordinates - does not always work so we use preceding G28\n;M106 P2 S0 ;turn off laser pointers - this is done by sms_prepare.sh script. no need to do twice\nM117 "Starting new GCode print job" ;M291 PMESSAGE does not work here. It just won't be displayed while printing
thumbnails = 
toolchange_gcode = 
use_firmware_retraction = 1
use_relative_e_distances = 0
use_volumetric_e = 1
variable_layer_height = 1
wipe = 0
z_offset = 0